Large Direct Shear Testing Machine


Clear selection
SKU: TS-2160, TS-2165. Categories: , . Tags: , , , , , , .
Large Direct Shear Testing Machine

The test covers the determination of consolidated drained shear strength of a soil material in direct shear. The machines are ideal for determining shear resistance of soil-geosynthetic / geomembrans by direct shear.
TS-2160 and TS-2165 Automatic Direct / Residual Shear Test Machines are motorised and floor mounted. The total vertical load on the specimen can reach up to 100 kN.
TS-2160 accepts up to 300 mm square shear box assembly.
TS-2065 accepts from 450 mm to 650 mm square shear box assemblies. All shear box assemblies are designed to contain water that surrounds the specimen. The Assemblies consist of a shear box with a rigid wall square or round hole complete with a vertical loading pad two retaining plates ( one is smooth, the other is peforated. The shear machines are driven by high resolution servo-motor and gear box assembly. Speed range is fully stepless variable over the range 0.00001 to 9.99999 mm/ min for both direction (forward and reverse). After test the reverse speed is 10 mm/min.). 100 kN load cell is used for load measurement. 200 x 0.01 mm sensitivity linear potentiometric transducers are used for vertical and horizontal displacement measurements. Horizontal Displacement limits are controlled by limit switches.

Display Unit and Controller

The 240 x 320 TFT Graphic Display is used for monitoring horizontal and vertical load and displacement values. All test parameters such as speed, failure condition etc. can be defined through this interface. The test can be started up and stopped by touch buttons.
The controller has two indepent control axes, one for horizontal motion one for vertical motion. The displacement on horizontal motion is measured through external displacement sensor fitted to frame and also through the encoder behind the servo motor. All calibration of sensors can be done easily by entering new points respect to the error.
The software is capable of monitoring all measured values and drawing Shear stress vs Horizontal displacement. After three runs with different normal loads, the software calculates the cohesion value ‘c’ and shear resistance angle ‘φ’ by using the best straight line fit.


  • BS 1377-7
  • ASTM D 6243
  • EN ISO 12957

  • Key Features

    User can select 3 different test types:

  • The machine run with the given speed to the direction of
    shear and stop when the load decreases

  • The machine run with the given speed to the direction
    of shear and also opposite direction until the given
    horizontal displacement

  • The machine run with the given speed to the direction
    of shear and also opposite direction until the given
    horizontal displacement and returns to home position with
    same speed

  • 4 analog channels for vertical load cell, vertical
    displacement, horizontal load and horizontal displacement
    transducer (one for each)

  • 1/65000 points resolution per channel
  • 1000 data per second sample rate for each channel. (In the
    software filtered as 10Hz)

  • Ethernet connecting for computer interface
  • 240×320 resolution 65535 colour TFT-LCD industrial

  • Free of charge PC software for the test control and
    advanced report generation

    The Direct and Residual shear software is developed according to BS 1377-7; ASTM D 6243; EN ISO 12957 standards to use with TS-2160 and TS- 2165 Machines. Direct residual and shear software consist of two sections. First section is used for the consolidation of the sample prior to shear.
    The software is capable of making three different types of test. The first type of the test is to move the machine till a load failure happens. On the second type of test the user can set a horizontal displacement and the test will continue until the machine reaches set value. On the last type of test, the machine can be configured as going to a set horizontal displacement value and return to home position.
    The software supports 5 different normal load values in order to calculate cohesion values. Prior to the test normal load value must be entered to the software. The normal stress value would be calculated respect to normal load and sample size automatically.
    The software supports both square type and round type samples. For both samples the area might be calculated by directly or by using the net area caused by horizontal displacement. The net area method is especially important for critical samples on academic literature.
    When the test is completed max and resilient stress values are recorded. The normal load versus max stress pair is used for calculating the cohesion value and angle.
    At least 3 loading with different normal loads are required for this property. One can set test speed, axis values etc through
    the setup of the software. The results can be submitted as a report or can be exported to Microsoft ExcelTM for advanced re-analyse procedures.

  • Product code TS-2160 TS-2165
    Speed Range 0.00001 to 9.99999 mm/min 0.00001 to 9.99999 mm/min
    Maximum Shear Force KN 100 100
    Maximum Vertical Load KN 100 100
    Horizontal Travel mm ± 100 ± 75
    Dimensions mm (W x D x H) 2000 x 1250 x 1900
    (900 x 800 x 450 – 650 shear box)
    (600 x 700 x 350 – 450 shear box)
    910 x 670 x 1200
    Weight Kg 2000 (Except shear box)
    (340 Kg – 650 mm shear box)
    (175 Kg – 450 mm shear box)
    Power W 1100 W at 220 V for hydraulic unit
    3500 W at 380 V for servo-motor
    220-240V, 50-60 Hz, 1ph

    The Automatic Direct Residual Shear Test Machine is supplied
    complete with:

  • 2 Load Cell 100 kN
  • 2 Linear Potentiometric Displacement Transducer (200 x 0.01 mm)
  • Software